|
|
|
10-14-2013, 03:22 PM | #1 |
Turbo Power
50
Rep 364
Posts |
FS: 135i aFe Axleback Exhaust - SOLD
I am buying a BMW PE because I am getting a great deal on one, so I want to sell my current one, which I had on the car for less than 500 miles. It is an aFe Mach Force XP Exhaust. Less than 500 miles on it! I am looking for $325 picked up or $400 shipped to 48 States in the US. Will ship International, but have to pay additional for shipping. Link to the product info page: http://www.**********s.com/aFe-Axle-...W-E82-135i.htm Link to how it sounds:
__________________
BSM 135i - CDV Delete | Bilstein | Eibach | M3 FSB | Whiteline
Last edited by TwinTurboed; 10-30-2013 at 07:43 AM.. |
10-15-2013, 08:54 AM | #4 |
Turbo Power
50
Rep 364
Posts |
My bad. I am located in Atlanta, GA. Thanks!
__________________
BSM 135i - CDV Delete | Bilstein | Eibach | M3 FSB | Whiteline
|
Appreciate
0
|
10-23-2013, 09:57 AM | #9 |
Turbo Power
50
Rep 364
Posts |
bump...this exhaust is $600 brand new! only asking 350$ for an almost brand new item.
__________________
BSM 135i - CDV Delete | Bilstein | Eibach | M3 FSB | Whiteline
|
Appreciate
0
|
10-23-2013, 10:13 AM | #11 |
Turbo Power
50
Rep 364
Posts |
The stock midpipe is still on the car, i just removed the oem axleback and replaced it with the aFe. It's a simple bolt-on, no cutting required.
__________________
BSM 135i - CDV Delete | Bilstein | Eibach | M3 FSB | Whiteline
|
Appreciate
0
|
10-23-2013, 11:15 AM | #12 |
Second Lieutenant
13
Rep 266
Posts |
Would it be possible to cut and weld a pipe onto that resonance chamber and take it to the other side for a quad setup? Im installing a 1m diffuser, if I can do that, that would save me a whole lot of headache.
Is their a path through the back side of the bumper for a 3" pipe to get on the other side? My cars apart, no bumper on can't tell much. |
Appreciate
0
|
10-23-2013, 12:49 PM | #13 | |
Turbo Power
50
Rep 364
Posts |
Quote:
__________________
BSM 135i - CDV Delete | Bilstein | Eibach | M3 FSB | Whiteline
|
|
Appreciate
0
|
10-23-2013, 08:47 PM | #15 | |
Turbo Power
50
Rep 364
Posts |
Quote:
Take a look at the attached picture (not the exhaust I am selling, but similar), that's where the clamps bolt on.
__________________
BSM 135i - CDV Delete | Bilstein | Eibach | M3 FSB | Whiteline
|
|
Appreciate
0
|
11-01-2013, 12:16 PM | #19 |
Pavement Operator
25
Rep 158
Posts |
How does the BMW PE compare? Just curious as I'm looking to choose between the two.
Thanks!
__________________
|
Appreciate
0
|
11-01-2013, 02:06 PM | #20 | |
Turbo Power
50
Rep 364
Posts |
Quote:
This exhaust will also be cheaper to buy and install because its simple. Where as with the PE, you have pay 900$ for the parts, then probably another $200 to get it installed unless you can DIY. Good luck!
__________________
BSM 135i - CDV Delete | Bilstein | Eibach | M3 FSB | Whiteline
|
|
Appreciate
0
|
11-01-2013, 02:09 PM | #21 | |
Pavement Operator
25
Rep 158
Posts |
Quote:
__________________
|
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|