My E24 refresh project [1983 633csi]

MPOWER5266 · 09-30-2022, 01:26 PM

I drove it for the first time last night, and then to work this morning, and I found some issues. Nothing major but things we need to address.

When the brakes are first pressed, it wants to pull to the right a hair before settling down. The floor mats are trash and pile up behind the clutch, they are just autozone cheepos. I want to get cocomats. The HVAC fan has two settings, off and f5 tornado. The car has been lowered on H&R springs and billy sports, it handles great but the big tires let it down. I would like to swap a z3 shifter in like we did on the E9, the stock unit is tight but tall and kinda gangly.

Other than that, its a really solid car and runs great. We had it on the lift and there is zero rust. The diff and trans are a little grimy from leaks but not bad. This is going to make a nice car.

Lady Jane · 10-03-2022, 09:02 AM

Quote:

Originally Posted by MPOWER5266

But yea we have nothing to do, so picked we picked up this nice little 1983 633csi.
Stay tuned.

Probably the most beautiful BMW of all times.

MPOWER5266 · 10-05-2022, 08:23 AM

Got started on the detail last night. But first my son had to inspect it.

Untitled by Nick Wood, on Flickr

He thinks we may need to dye the seats but we can get away with a good cleaning first.

Untitled by Nick Wood, on Flickr

My daughter had no opinion. So I went ahead and gave it a good wash with Adams Strip wash to remove any waxes or sealants that may have been on the car.

Untitled by Nick Wood, on Flickr

Then I hit it with some Adams Iron remover.

by Nick Wood, on Flickr

There wasn't much on there, but it did pull some from the roof and quarter panel.

Untitled by Nick Wood, on Flickr

Then I gave it a claybar.

Untitled by Nick Wood, on Flickr

I did a couple test spots and I think its going to come out great. Its hard to see but the lower half of this photo is a test spot.

Untitled by Nick Wood, on Flickr

The 1/4 that looked like it had a blended spot doesnt seem to have a clear coat. I am a little concerned about that but I will start there and see what I can do to make it look better. We may eventually have that resprayed. I will get it taped up and hopefully finish compounding it tonight.

MPOWER5266 · 10-06-2022, 08:28 AM

Started on the paint correction last night. The first step was taping up all of the trim on this thing.

Untitled by Nick Wood, on Flickr

Got my weapons prepped. I am honestly pretty happy with the cheapo 3" polisher I picked up for this project.

Untitled by Nick Wood, on Flickr

Untitled by Nick Wood, on Flickr

I was going to go with Jescar Compound, but I was running a little low. I used Megs 105 and other than the dust, I am happy with the results.

Untitled by Nick Wood, on Flickr

Here is a before and after of the passenger door.

Untitled by Nick Wood, on Flickr

And after Megs 105 with a microfiber pad.

Untitled by Nick Wood, on Flickr

Hood.

Untitled by Nick Wood, on Flickr

Untitled by Nick Wood, on Flickr

And fully compounded.

Untitled by Nick Wood, on Flickr

I am hoping to finish the polish tonight and the majority of the detail over this weekend.

P1 · 10-07-2022, 12:44 AM

Love seeing what a difference a good detail can make.

MPOWER5266 · 10-10-2022, 08:18 AM

Made more progress on the e24 this weekend. Friday night my buddy came over and hung out while I polished the car. I am pretty happy with the results.

Untitled by Nick Wood, on Flickr

Untitled by Nick Wood, on Flickr

Shiny…

Untitled by Nick Wood, on Flickr

Took it pretty easy Saturday, I had other projects to work on. I did put the first coat of sealant on. Today I got started bright and early.

Untitled by Nick Wood, on Flickr

Started off cleaning the trim and putting solution finish on it. Before.

Untitled by Nick Wood, on Flickr

After.

Untitled by Nick Wood, on Flickr

I then put the second coat of sealant on the paint.

Untitled by Nick Wood, on Flickr

After that, came my least favorite part of car cleaning, the interior….

Untitled by Nick Wood, on Flickr

It was fairly easy to clean the dash, door panels, etc etc. And it needed it.

Untitled by Nick Wood, on Flickr

Untitled by Nick Wood, on Flickr

The leather was next and it was rough.

Untitled by Nick Wood, on Flickr

It just took a lot of scrubbing and contorting myself into weird positions.. Here are some before/after/progress pics..

Untitled by Nick Wood, on Flickr

Untitled by Nick Wood, on Flickr

This was a brand new towel. This was just from the passenger seat...

Untitled by Nick Wood, on Flickr

After about 2 hours.

Untitled by Nick Wood, on Flickr

I still need to condition the leather, clean the carpets, glass, coat the trim, wheels/tires, and one more coat of wax on the paint. Hopefully I’ll have it done in time for cars and coffee Saturday.

overcoil · 10-10-2022, 01:41 PM

Those seats look great. I wonder if BMW still offers the padding foam/filler thru a Classic Center.

MPOWER5266 · 10-11-2022, 08:13 AM

Quote:

Originally Posted by Caravaggio

Those seats look great. I wonder if BMW still offers the padding foam/filler thru a Classic Center.

I am not sure, but my dad and I used memory foam in my 2002's seats. It came out awesome, and thats probably all I will use from now on.

Very small update. I was tired after work last night so I didn't do a ton. I did vac and clean the carpets. Before.

Untitled by Nick Wood, on Flickr

After. It looks a little dark but it was wet. This morning it had dried out nicely.

Untitled by Nick Wood, on Flickr

Untitled by Nick Wood, on Flickr

Then I conditioned the seats.

Untitled by Nick Wood, on Flickr

No photos but I cleaned the inside windows and coated the trim. After that I put a coat of collinite 845 on the paint.

Untitled by Nick Wood, on Flickr

I am pretty close to finishing it up. I just need to coat the glass, clean the wheels(I am not going to remove them to clean them, just wipe them down), and dress the tires. I should have it done in time for cars and coffee this weekend.

tracer bullet · 10-11-2022, 09:13 AM

Seems like this doesn't need nearly as much work as your last project documented here. Is there a lot more to do mechanically or do you think you'll be fairly happy with this one after giving it a good cleaning (and paint correction and so forth of course being included in that)?

MPOWER5266 · 10-11-2022, 09:18 AM

Quote:

Originally Posted by tracer bullet

Seems like this doesn't need nearly as much work as your last project documented here. Is there a lot more to do mechanically or do you think you'll be fairly happy with this one after giving it a good cleaning (and paint correction and so forth of course being included in that)?

It really doesn't need much, just some leaks and small maintenance.

MPOWER5266 · 10-12-2022, 08:31 AM

I put the finishing touches on the detail last night and over all I am pretty happy with it.

Untitled by Nick Wood, on Flickr

Untitled by Nick Wood, on Flickr

I also tossed the mats out of my wagon in for now, they seem to work okay. I think we will eventually find some cocomats for it.

Untitled by Nick Wood, on Flickr

I was hoping to get it out this afternoon for some better pictures but we have rain until Friday and I want to keep it clean for cars and coffee Saturday morning. I think the plan for now is to address some leaks, find a steering wheel, z3 short shifter, and hopefully exhaust(the muffler needs to be replaced. ) I am also on the hunt for some wheels, which will need restoration I am sure.

P1 · 10-13-2022, 10:02 PM

She looks extra long in those last few pics. Detail did wonders.

Which products do you use for the interior?

Cos270 · 10-14-2022, 08:45 AM

A little off topic but is that M-sport speckled paint flakes in your epoxy floor??? Awesome touch!

MPOWER5266 · 10-14-2022, 12:34 PM

Quote:

Originally Posted by P1

She looks extra long in those last few pics. Detail did wonders.

Which products do you use for the interior?

P&S interior on the plastic bits, simple green xtreme on the carpet( I am going to go back in steam it), colourlock heavy leather cleaner, and Nuvite conditioner(just something I sell at work its okay.)

MPOWER5266 · 10-14-2022, 12:36 PM

Quote:

Originally Posted by Cos270

A little off topic but is that M-sport speckled paint flakes in your epoxy floor??? Awesome touch!

Good eye.

Mani59 · 10-14-2022, 03:26 PM

"Pretty happy with it"

You should be absolutely delighted with it - it looks absolutely stunning and you should be very proud of your efforts!

IcewaterPete · 10-16-2022, 10:35 PM

Very nice work! You found a real gem.

MPOWER5266 · 12-05-2022, 08:58 AM

Small e24 updates.... As you can see in this photo the weird little cover dealies(no clue what to call them) were looking pretty rough.

Untitled by Nick Wood, on Flickr

So we pulled them to re-glue.

Untitled by Nick Wood, on Flickr

Added new speakers. I am not an audiophile so these will be fine..

Untitled by Nick Wood, on Flickr

Cleaned them and reinstalled.

Untitled by Nick Wood, on Flickr

The exhaust didnt sound great and had a "putty" patch on it. We removed the patch to see if it could be repaired... its a lost cause so a Billy Boat exhaust is on the way.

Untitled by Nick Wood, on Flickr

Since we are waiting on the exhaust, it seemed like a good time to fix some other stuff. Leaks on the trans and diff were addressed and cleaned.

Untitled by Nick Wood, on Flickr

And the tired old shifter was pulled and replaced with a Z3 lever.

Untitled by Nick Wood, on Flickr

Hopefully the e24 will be done in the next week or so and we can do some little things on the e9 before putting the Jeep Cherokee Chief project on the lift.

Untitled by Nick Wood, on Flickr

MPOWER5266 · 12-06-2022, 02:19 PM

Oh, almost forgot, antenna override installed. This and the e9 both have power antennas that would come up when the radio is powered on, but since I pretty much just use bluetooth in both, I hate that the antenna is up. This allows you to have the head unit on but the antenna down.

Untitled by Nick Wood, on Flickr

IcewaterPete · 12-07-2022, 10:33 PM

Very impressive progress.

MPOWER5266 · 12-19-2022, 10:06 AM

Small update on the E24. The exhaust showed up.

Untitled by Nick Wood, on Flickr

But the mid pipes were wrong so they are going back to Billy boat. Since we are holding on that we decided to pull the rear package tray.

Untitled by Nick Wood, on Flickr

We tried cleaning it but it seemed like it would be better to just re-dye it.

Untitled by Nick Wood, on Flickr

Much better.

Untitled by Nick Wood, on Flickr

We may re-dye the seats soon. Just waiting on the exhaust parts to come in right now.

MPOWER5266 · 01-09-2023, 12:22 PM

Micro update. The last couple weeks have been nuts. Between work, holidays, and a death in the family we haven't had much free time.

We got the parts back from Billy Boat and finally got the exhaust hung. It sounds good.

Untitled by Nick Wood, on Flickr

And since the rear seats were out, we dropped one off at our local upholstery shop to fix this seam.

Untitled by Nick Wood, on Flickr

And started to dye the other seat and rear center console with Colourlock.

Untitled by Nick Wood, on Flickr

Untitled by Nick Wood, on Flickr

More soon.

09-30-2022, 01:26 PM	#23
MPOWER5266 Major 4778 Rep 1,189 Posts Drives: 1997 Dinan m3 Join Date: Oct 2017 Location: Ga iTrader: (0)	I drove it for the first time last night, and then to work this morning, and I found some issues. Nothing major but things we need to address. When the brakes are first pressed, it wants to pull to the right a hair before settling down. The floor mats are trash and pile up behind the clutch, they are just autozone cheepos. I want to get cocomats. The HVAC fan has two settings, off and f5 tornado. The car has been lowered on H&R springs and billy sports, it handles great but the big tires let it down. I would like to swap a z3 shifter in like we did on the E9, the stock unit is tight but tall and kinda gangly. Other than that, its a really solid car and runs great. We had it on the lift and there is zero rust. The diff and trans are a little grimy from leaks but not bad. This is going to make a nice car.
	Appreciate 0 Quote

10-05-2022, 08:23 AM	#25
MPOWER5266 Major 4778 Rep 1,189 Posts Drives: 1997 Dinan m3 Join Date: Oct 2017 Location: Ga iTrader: (0)	Got started on the detail last night. But first my son had to inspect it. Untitled by Nick Wood, on Flickr He thinks we may need to dye the seats but we can get away with a good cleaning first. Untitled by Nick Wood, on Flickr My daughter had no opinion. So I went ahead and gave it a good wash with Adams Strip wash to remove any waxes or sealants that may have been on the car. Untitled by Nick Wood, on Flickr Then I hit it with some Adams Iron remover. by Nick Wood, on Flickr There wasn't much on there, but it did pull some from the roof and quarter panel. Untitled by Nick Wood, on Flickr Then I gave it a claybar. Untitled by Nick Wood, on Flickr I did a couple test spots and I think its going to come out great. Its hard to see but the lower half of this photo is a test spot. Untitled by Nick Wood, on Flickr The 1/4 that looked like it had a blended spot doesnt seem to have a clear coat. I am a little concerned about that but I will start there and see what I can do to make it look better. We may eventually have that resprayed. I will get it taped up and hopefully finish compounding it tonight.
	Appreciate 5 Almuliman560.50 spazzyfry1235013.50 Mani5915861.50 FrankDK186.50 IcewaterPete2743.50 Quote

10-06-2022, 08:28 AM	#26
MPOWER5266 Major 4778 Rep 1,189 Posts Drives: 1997 Dinan m3 Join Date: Oct 2017 Location: Ga iTrader: (0)	Started on the paint correction last night. The first step was taping up all of the trim on this thing. Untitled by Nick Wood, on Flickr Got my weapons prepped. I am honestly pretty happy with the cheapo 3" polisher I picked up for this project. Untitled by Nick Wood, on Flickr Untitled by Nick Wood, on Flickr I was going to go with Jescar Compound, but I was running a little low. I used Megs 105 and other than the dust, I am happy with the results. Untitled by Nick Wood, on Flickr Here is a before and after of the passenger door. Untitled by Nick Wood, on Flickr And after Megs 105 with a microfiber pad. Untitled by Nick Wood, on Flickr Hood. Untitled by Nick Wood, on Flickr Untitled by Nick Wood, on Flickr And fully compounded. Untitled by Nick Wood, on Flickr I am hoping to finish the polish tonight and the majority of the detail over this weekend.
	Appreciate 10 Lady Jane81982.00 Hagasan41333.50 P111727.00 tracer bullet3733.50 overcoil3121.00 GERMAN M34227.00 Mani5915861.50 FrankDK186.50 IcewaterPete2743.50 happyjack1756.00 Quote

10-07-2022, 12:44 AM	#27
P1 Lieutenant General 11727 Rep 11,191 Posts Drives: 2004 3/4 ton Duramax Join Date: Aug 2007 Location: United States iTrader: (1)	Love seeing what a difference a good detail can make.
	Appreciate 0 Quote

10-10-2022, 08:18 AM	#28
MPOWER5266 Major 4778 Rep 1,189 Posts Drives: 1997 Dinan m3 Join Date: Oct 2017 Location: Ga iTrader: (0)	Made more progress on the e24 this weekend. Friday night my buddy came over and hung out while I polished the car. I am pretty happy with the results. Untitled by Nick Wood, on Flickr Untitled by Nick Wood, on Flickr Untitled by Nick Wood, on Flickr Shiny… Untitled by Nick Wood, on Flickr Took it pretty easy Saturday, I had other projects to work on. I did put the first coat of sealant on. Today I got started bright and early. Untitled by Nick Wood, on Flickr Started off cleaning the trim and putting solution finish on it. Before. Untitled by Nick Wood, on Flickr After. Untitled by Nick Wood, on Flickr I then put the second coat of sealant on the paint. Untitled by Nick Wood, on Flickr After that, came my least favorite part of car cleaning, the interior…. Untitled by Nick Wood, on Flickr It was fairly easy to clean the dash, door panels, etc etc. And it needed it. Untitled by Nick Wood, on Flickr Untitled by Nick Wood, on Flickr The leather was next and it was rough. Untitled by Nick Wood, on Flickr It just took a lot of scrubbing and contorting myself into weird positions.. Here are some before/after/progress pics.. Untitled by Nick Wood, on Flickr Untitled by Nick Wood, on Flickr Untitled by Nick Wood, on Flickr This was a brand new towel. This was just from the passenger seat... Untitled by Nick Wood, on Flickr After about 2 hours. Untitled by Nick Wood, on Flickr I still need to condition the leather, clean the carpets, glass, coat the trim, wheels/tires, and one more coat of wax on the paint. Hopefully I’ll have it done in time for cars and coffee Saturday.
	Appreciate 6 Almuliman560.50 Cos270610.00 Davil6885.50 Mani5915861.50 FrankDK186.50 IcewaterPete2743.50 Quote

10-10-2022, 01:41 PM	#29
overcoil Major General 3121 Rep 5,582 Posts Drives: M235i 6spd Join Date: Dec 2013 Location: Mid-Atlantic iTrader: (0)	Those seats look great. I wonder if BMW still offers the padding foam/filler thru a Classic Center.
	Appreciate 0 Quote

10-11-2022, 09:13 AM	#31
tracer bullet Brigadier General 3734 Rep 4,259 Posts Drives: '25 Z4, '15 X3 35i (135i sold) Join Date: May 2011 Location: Saint Paul, MN iTrader: (1)	Seems like this doesn't need nearly as much work as your last project documented here. Is there a lot more to do mechanically or do you think you'll be fairly happy with this one after giving it a good cleaning (and paint correction and so forth of course being included in that)?
	Appreciate 0 Quote

10-12-2022, 08:31 AM	#33
MPOWER5266 Major 4778 Rep 1,189 Posts Drives: 1997 Dinan m3 Join Date: Oct 2017 Location: Ga iTrader: (0)	I put the finishing touches on the detail last night and over all I am pretty happy with it. Untitled by Nick Wood, on Flickr Untitled by Nick Wood, on Flickr I also tossed the mats out of my wagon in for now, they seem to work okay. I think we will eventually find some cocomats for it. Untitled by Nick Wood, on Flickr I was hoping to get it out this afternoon for some better pictures but we have rain until Friday and I want to keep it clean for cars and coffee Saturday morning. I think the plan for now is to address some leaks, find a steering wheel, z3 short shifter, and hopefully exhaust(the muffler needs to be replaced. ) I am also on the hunt for some wheels, which will need restoration I am sure.
	Appreciate 7 Almuliman560.50 P111727.00 Mani5915861.50 FrankDK186.50 Chappers 715958.00 IcewaterPete2743.50 happyjack1756.00 Quote

10-13-2022, 10:02 PM	#34
P1 Lieutenant General 11727 Rep 11,191 Posts Drives: 2004 3/4 ton Duramax Join Date: Aug 2007 Location: United States iTrader: (1)	She looks extra long in those last few pics. Detail did wonders. Which products do you use for the interior?
	Appreciate 0 Quote

10-14-2022, 08:45 AM	#35
Cos270 First Lieutenant 610 Rep 373 Posts Drives: 2015 M235i Join Date: Sep 2018 Location: MI iTrader: (0) Garage List 2015 F22 M235i [0.00]	A little off topic but is that M-sport speckled paint flakes in your epoxy floor??? Awesome touch!
	Appreciate 0 Quote

10-14-2022, 03:26 PM	#38
Mani59 Moderator 15862 Rep 8,140 Posts Drives: F32 435i Luxury & G26 i4 35 Join Date: Nov 2010 Location: Leicestershire iTrader: (1)	"Pretty happy with it" You should be absolutely delighted with it - it looks absolutely stunning and you should be very proud of your efforts! __________________ Visit my (mainly) BMW gallery http://jetone.co.uk and BMW miniature model collection http://bmw-miniatures.co.uk
	Appreciate 1 MPOWER52664778.00 Quote

10-16-2022, 10:35 PM	#39
IcewaterPete Lieutenant Colonel 2744 Rep 1,796 Posts Drives: 2020 F33 M Sport, 2021 M2C 6MT Join Date: Sep 2020 Location: Illinois iTrader: (0)	Very nice work! You found a real gem.
	Appreciate 1 MPOWER52664778.00 Quote

12-05-2022, 08:58 AM	#40
MPOWER5266 Major 4778 Rep 1,189 Posts Drives: 1997 Dinan m3 Join Date: Oct 2017 Location: Ga iTrader: (0)	Small e24 updates.... As you can see in this photo the weird little cover dealies(no clue what to call them) were looking pretty rough. Untitled by Nick Wood, on Flickr So we pulled them to re-glue. Untitled by Nick Wood, on Flickr Added new speakers. I am not an audiophile so these will be fine.. Untitled by Nick Wood, on Flickr Cleaned them and reinstalled. Untitled by Nick Wood, on Flickr The exhaust didnt sound great and had a "putty" patch on it. We removed the patch to see if it could be repaired... its a lost cause so a Billy Boat exhaust is on the way. Untitled by Nick Wood, on Flickr Since we are waiting on the exhaust, it seemed like a good time to fix some other stuff. Leaks on the trans and diff were addressed and cleaned. Untitled by Nick Wood, on Flickr And the tired old shifter was pulled and replaced with a Z3 lever. Untitled by Nick Wood, on Flickr Hopefully the e24 will be done in the next week or so and we can do some little things on the e9 before putting the Jeep Cherokee Chief project on the lift. Untitled by Nick Wood, on Flickr
	Appreciate 6 Almuliman560.50 P111727.00 IcewaterPete2743.50 Chappers 715958.00 Mani5915861.50 happyjack1756.00 Quote

12-06-2022, 02:19 PM	#41
MPOWER5266 Major 4778 Rep 1,189 Posts Drives: 1997 Dinan m3 Join Date: Oct 2017 Location: Ga iTrader: (0)	Oh, almost forgot, antenna override installed. This and the e9 both have power antennas that would come up when the radio is powered on, but since I pretty much just use bluetooth in both, I hate that the antenna is up. This allows you to have the head unit on but the antenna down. Untitled by Nick Wood, on Flickr
	Appreciate 3 P111727.00 IcewaterPete2743.50 Mani5915861.50 Quote

12-07-2022, 10:33 PM	#42
IcewaterPete Lieutenant Colonel 2744 Rep 1,796 Posts Drives: 2020 F33 M Sport, 2021 M2C 6MT Join Date: Sep 2020 Location: Illinois iTrader: (0)	Very impressive progress.
	Appreciate 0 Quote

12-19-2022, 10:06 AM	#43
MPOWER5266 Major 4778 Rep 1,189 Posts Drives: 1997 Dinan m3 Join Date: Oct 2017 Location: Ga iTrader: (0)	Small update on the E24. The exhaust showed up. Untitled by Nick Wood, on Flickr But the mid pipes were wrong so they are going back to Billy boat. Since we are holding on that we decided to pull the rear package tray. Untitled by Nick Wood, on Flickr We tried cleaning it but it seemed like it would be better to just re-dye it. Untitled by Nick Wood, on Flickr Much better. Untitled by Nick Wood, on Flickr We may re-dye the seats soon. Just waiting on the exhaust parts to come in right now.
	Appreciate 1 IcewaterPete2743.50 Quote

01-09-2023, 12:22 PM	#44
MPOWER5266 Major 4778 Rep 1,189 Posts Drives: 1997 Dinan m3 Join Date: Oct 2017 Location: Ga iTrader: (0)	Micro update. The last couple weeks have been nuts. Between work, holidays, and a death in the family we haven't had much free time. We got the parts back from Billy Boat and finally got the exhaust hung. It sounds good. Untitled by Nick Wood, on Flickr And since the rear seats were out, we dropped one off at our local upholstery shop to fix this seam. Untitled by Nick Wood, on Flickr And started to dye the other seat and rear center console with Colourlock. Untitled by Nick Wood, on Flickr Untitled by Nick Wood, on Flickr More soon.
	Appreciate 3 Cos270610.00 Almuliman560.50 IcewaterPete2743.50 Quote